lock nut
英 [lɒk nʌt]
美 [lɑːk nʌt]
锁紧（防松，保险）螺帽
双语例句
- The problems in lock nut of roll axis and sleeve of precision rolling mill are analyzed, some measures proposed, good result got.
针对高速线材生产中，精轧机辊轴及隔套锁紧螺母存在的问题进行分析，提出了改进措施，取得了较好效果。 - Tighten lock nut from camber eccentric to the prescribed tightening torque tightening torques for rear axle.
将外倾角偏心装置的锁紧螺母紧固至规定的拧紧力矩后轴的拧紧力矩。 - Eccentric screw and lock nut are only tightened to the prescribed tightening torque during suspension alignment!
偏心螺钉和锁紧螺母仅在悬架定位期间拧紧至规定的拧紧力矩！ - Lock nut of iron or stee
锁紧螺帽，防松螺帽，铁或钢制 - Install adjuster nut and lock nut.
安装调节器螺母和防松螺母。 - If only one locating ring is required, it should be inserted on the same side as the lock nut.
如果只需一个定位环，此定位环应插入与锁紧螺母相同的一侧。 - To do this, loosen the lock nut approx.3 turns.
要执行此操作，请松开锁紧螺母约3圈。 - Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem.
松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。 - Wheel bolts, nuts, lock nuts, weld nut, spring nut, washer, copper fasteners, stainless steel fasteners and other automotive fasteners.
车轮螺栓、螺母，锁紧螺母，焊接螺母，簧片螺母，垫圈，铜紧固件，不锈钢紧固件，其他汽车紧固件。 - To Readjust-Loosen lock nut on the adjusting screw.
重新调节：松开调节螺丝上的锁定螺母。 - Tighten lock nut for the drive shaft to the specified tightening torque.
将驱动轴的锁紧螺母拧紧至规定的拧紧力矩。 - Can counterclockwise unscrewing the grip the lock nut and adjust control again, until the nut spin twist clearance fit.
可以逆时针拧松握把根部的锁紧螺母，再左右旋拧调整螺母，直到间隙合适为止。 - Smaller sizes use a lock nut with a locking washer, larger sizes use a nut with locking clip.
小尺寸轴承使用带锁紧垫圈的锁紧螺母大尺寸的轴承使用带锁紧卡箍的锁紧螺母。 - The lock nut must first be loosened.
但必须首先拧松锁紧螺母。 - Hexagon bolts and nuts, hexagon socket head cap screws, thread bar, carriage bolts, Nylon lock hex nut, flat washer, fish bolt set, standard fasteners etc.
六角螺母，六角螺栓，自攻钉，牙棒等。非标件生产与出口。 - The mother of nylon lock, metal lock master, K cap, hex nut, cap-shaped, butterfly hats and all kinds of washers, retaining rings, pins and so on.
尼龙锁紧母、金属锁紧母、K帽、六角螺母、盖帽形、蝶形帽及各式垫圈、挡圈、销类等。 - Reformed the structure of pump shaft, increased diameter of shaft located the position of pump thrust bearing lock nut, improved the strength of pump shaft, extended the service life of pump shaft.
改进泵轴结构，在泵轴推力轴承锁紧螺母处加大轴径，提高了泵轴强度，延长了泵轴的使用寿命。 - The feasibility of repetitive use of Fe-based shape memory alloy lock nut has been studied in order to lower the usage cost.
为了降低铁基形状记忆合金防松螺母的使用成本，探索了该新型螺母重复使用的可行性。 - The fracture of the pump shaft is mainly caused by large size non metallic inclusions and point welding between the lock nut and the pump shaft.
结果表明，大尺寸的非金属夹杂和背帽外缘的点焊是引起泵轴过早断裂的主要原因。